Shopping Cart

My Cart

items

You have no items in your shopping cart.

TB-250 TB-500

Click on above image to view full picture

  • TB-250 TB-500

G-TEC Natural Gas Torch Booster TB-500

Quick Overview

A Torch Booster is easy to use! When your torch is not lit the Torch Booster automatically goes into recirculation mode.
$11,200.00 11200 $

SKU: MSW-998-TB-500

Availability: In stock

Ships From: Philadelphia PA

 

G-TEC Natural Gas Torch Booster TB-500

Lead Time: Typically 3 Weeks. Contact us for any lead time concerns.

When your gas utility is unable to provide enough pressure to operate you Shrinkfast Heat Tool, a G-TEC Natural Gas Torch Booster will give ou all the flow you need.  Torch Boosters are easy to connect to the gas pipe, easy to operate, and they supply gas at a proper pressure all day.  Turn the system on at the start of the day and off after the last shift - it's like a gas cylinder that never runs empty!

When your torch is not lit, the Torch Booster automatically goes into recirculation mode. It is designed to be left running for short periods when torches are not being used and does not require operator attention as torches are turned on and off.  TB-500 Torch Boosters are Certified by CSA International, CE Compliant and are permitted in buildings that prohibit gases in cylinders such as acetylene and propane.

The TB-500 Torch Booster will fuel up to 5 Shrinkfast Model 975, or 3 Shrinkfast Model 998.

The G-TEC TB-500 Natural Gas Torch Booster Additional Info:

  • Boosts Gas Pressure to 45psi at 550scfh**
  • Gas Supply can be 1/4 to 5psi in a 1.5" pipe.
  • Electrical requirement is 208V single phase 30A 60Hz or 230V single phase 30A 50Hz
  • Attach Shrinkfast regulator to high-pressure outlet to set pressure at 15psi for best performance
  • Cabinet is 28" W x 20" T x 24" D
  • Unit weighs 285lbs
  • No special site environmental preparation required
  • Ambient temperature should be between 40-90F
  • Cooling module required if >90F or >16 hours runtime
    ** Supply pressure greater than 1/4psi increases system output to support more heat tools.

Here are several reasons to use high pressure natural gas with your heat tool:

1. For equal BTUs, natural gas is up to 75% less expensive than propane.
2. Natural gas is safer than propane. Because natural gas is lighter than air, leaks rise and dissipate. Propane however, is heavier than air, so leaks sink to the lowest spot in the facility and wait for a spark.
3. With a G-TEC Torch Booster, you eliminate cylinders of stored propane in your building. In the case of an emergency, propane cylinders make an already dangerous situation worse. G-TEC Torch Boosters do not store gas – they boost pressure from your natural gas supply to the heat tool as gas is used.
4. What our customers like best is they never run out of gas. There are no small propane cylinders to run empty, no need to remove and reinstall individual pressure regulators, and emergency gas deliveries are never needed.

Be sure to look at Mr. Shrinkwrap's Shrink Wrap Installation Supplies page for Crosswoven Strap, Tape, Vents, Zipper Doors, or other items you might need for your project.

Mr. Shrinkwrap is a leading distributor of protective products, shrink wrap films and installation supplies with a dedicated team available to take your order at any time of day. We have several experienced shrink wrap installation technicians on staff to help and support you on various aspects of any shrink wrap project. If you would like to place an order over the phone or have questions for us, give Mr. Shrinkwrap a call at 800-847-5290.

Free Shipping No

Back to top of page