800-847-5290

ShrinkCover Standard Modular Cover — Fits 8 ft × 38 ft × 6 ft

$987.49
Availability: In stock
SKU
MSW-SC-MOD-0838-60

Fits a load 35 ft 3 in – 38 ft 0 in long, 7 ft 5 in – 8 ft 0 in wide, 5 ft 7 in – 6 ft 0 in tall. Low-profile ShrinkShield cover for skids, racks and packaged equipment — cut to spec, sewn, heat-shrunk tight on site. Comes complete with a base drawstring around the perimeter of the opening. Made to order, 3–5 weeks. Add to Quote.

This is the long end of the range. A 8 ft × 38 ft × 6 ft ShrinkCover does one job: protect a finished unit in transit from the factory. At these dimensions that normally means long low steel, extended pipe racks, multi-skid assemblies and conveyor sections that take up the whole deck.

What this size fits

  • Length: 35 ft 3 in – 38 ft 0 in
  • Width: 7 ft 5 in – 8 ft 0 in
  • Height: 5 ft 7 in – 6 ft 0 in

Those bands describe the object being covered, not the cut size of the cover. Measure the unit at its widest, longest and tallest point, including anything that projects, and pick the band that contains it. This cover finishes at roughly 908 sq ft of ShrinkShield.

On the road at 8 ft wide

At 8 ft wide the unit sits inside normal deck width. Nothing about the shipment is unusual to a carrier, so the cover is doing weather, road grit and stone-chip duty rather than solving a permit problem. At this length the unit takes the full deck and the cover sees more airflow than any other size in the range: leading edge, full length, every mile. Seam placement and a tight shrink matter more here than anywhere else.

How it is built

Each cover is cut 3% larger than the measured load, sewn to spec as a box with an open bottom, then heat-shrunk onto the unit on site. The fabric is ShrinkShield — 7 mil, white, triple-layer. It will take up to 12% shrink and 10% is the design target, and that is the step that pulls the panel down tight to the frame instead of leaving it loose on the load. The 6 ft height class uses about 24% less fabric than the 9 ft class over the same footprint. That is the largest single cost lever available on a low load, so size the height class to the equipment rather than to the trailer. Each standard cover comes complete with a base drawstring around the perimeter of the opening.

The result is the wedge: cut to spec, sewn, and heat-shrunk tight to the load. It does not flap in transit, and it does not have to be re-tensioned at every fuel stop.

Accessories worth specifying

A skid or equipment module that gets opened at the receiving yard should have a zipper access door (MSW-800CONFIG) taped in before it ships — a receiver can then check or energise the unit without slitting the panel and giving up the seal for the rest of the journey. Corner guards (MSW-802) go on the hard points where the shrink pulls tightest: skid frame corners, lifting lugs, anything square enough to work a hole through from the inside. Where the carrier runs chain or strap across the load, a poly-woven strap protector (MSW-801) takes the abrasion instead of the fabric. Cross-woven strapping cord (MSW-500) is what the install crew bands the panel down with before heat goes on.

Lead time and ordering

Made to order, 3–5 weeks. Send dimensions and quantity through Add to Quote and the quote desk will come back with the figure and a build slot. If your unit falls outside these bands, the custom program covers it — ask on the same request.

More Information
SKUMSW-SC-MOD-0838-60
Weight43.000000
BrandShrinkCover
Cover Width8 ft
Cover Length38 ft
Cover Height6 ft
Fits Width7 ft 5 in – 8 ft 0 in
Fits Length35 ft 3 in – 38 ft 0 in
Fits Height5 ft 7 in – 6 ft 0 in
Cover Area (sq ft)908
ConstructionSewn to spec, heat-shrunk
Item ReturnsThis item can be returned

Need Assistance? Get a Custom Quote!

We’re here to help! If you have any questions about this product or need a custom quote, feel free to:

  • 📞 Call us at 800-847-5290
  • 💬 Use our live chat (bottom right corner)
  • 📝 Select your desired quantity and click "Add to Quote" to submit your request

📍 Looking for a custom solution? Many of our products can be customized with larger quantity orders. Visit our Custom Products page to explore customization options.

📩 Need more details? Visit our Contact Us page for our address, phone number, and a contact form to reach our team.

Our team is happy to discuss your needs and provide the best pricing and recommendations for your project!

Customer Questions
No Questions
Please, mind that only logged in users can submit questions
More from ShrinkCover

Customer Also Bought