Free Standing 3 Post Titan Ultra Stretch Wrapping System 4100-35FA by Cousins

Free Standing 3 Post Titan Ultra Stretch Wrapping System 4100-35FA by Cousins

Request a quote for accurate shipping costs - fast estimates are likely incorrect.

**Lead Time up to 4-5 Weeks ** Unit manufactured in and shipped from Canada. Units shipping outside of Canada may be subject to additional customs/broker fees. Please contact beforehand for official rate quote.

Note: A choice of five different frame variations are available allowing these systems to be tailored to suit specific floor space, material handling and wrapping requirements. Select from wall-mount (WM), post-mount (PM), free-standing rear mount (FSR), free-standing 3-post (FS3), and free-standing ‘U’-shaped (FSU) frame versions.




GENERAL SPECIFICATIONS

PRODUCTION SPEED
• 1-35 loads per hour
NOTE: Process rates will vary with load size, number of wraps & load/unload time

LOAD CAPACITY
• Maximum load weight: Unlimited (floor supported)
• Maximum load size: 50” W x 50” L (71” max. load diagonal) x 86” H (plus up to 4” top overlap)
• Minimum load size: 24” W x 24” L x 24” H

ROTARY ARM
• Double flange bearing support system
• Twin V-belt drive pulleys with belt tensioner
• 1-12 RPM rotational speed c/w soft start acceleration
• Final revolution deceleration and positive stop alignment
• 1/2 HP DC variable speed motor

FILM CARRIAGE ELEVATOR
• 1/2 HP DC variable speed motor
• Direct flat belt drive system
• Maintenance free 12 point carriage guidance system

FILM DELIVERY SYSTEM
• NEW Super Rapid Thread II ™ 20” capacity pre-stretch film carriage
• Special Film Threading Device – Uniquely orientates the sticky side of the film against the pre-stretch rollers and the inside of the load.
• 1/2 HP DC variable speed motor
• Fully electronic dynamic dancer corner compensation
• 33 to 313% fixed stretch capability
• Pre-stretch ratio variable by easy sprocket change
• Rapid Thread ™ Safety Door with auto power cut-off switch
• Superior film-to-roller contact area
• Lifetime warranty on pre-stretch rollers

AUTOMATION FEATURES
“All Electric – No Pneumatics Required”
• Electro-mechanically actuated film clamp mechanism
• Electro-mechanically actuated film tail cut/wipe arm mechanism
• Ni-chrome impulse hot wire film cut off c/w automatic periodic cleaning cycle

CONTROL FEATURES
• PANASONIC PLC with Touchscreen Operator Interface
• Power Off – On – Reset Switch & Power On indicator light
• Single button Auto Wrap Cycle Start/Pause
• Cycle Pause for applying top sheets
• Reinforce Wrap control for mid-wrapping
• Emergency Stop button
• Rotary Arm Jog button
• Film Carriage Lower/Raise buttons
• Film Clamp Open/Close button
• Film tension (Force-to-Load) control
• Separate film carriage raise & lower speed controls
• Variable rotary arm speed control
• Triple beam auto load height sensing photo-eye, detects dark or shiny loads
• Separate 1 to 12 revolution top & bottom wrap control
• Selectable Reduced Bottom Film Force parameter for wrapping bottom of load
• A – B – C Wrap Program selector with capability to input and store unique wrapping parameters for each program
• Pendant Start/Stop push-button station for remote operator control – optional lanyard or wireless remote control available
• Stack-light beacon indicates run, clear or fault conditions
• Rotary arm and film carriage elevator dynamic braking
• NEMA 12 control panel and junction boxes
• Dust tight slip ring assembly
• Non-proprietary UL/CSA approved components

STRUCTURAL FEATURES
• All structural steel construction
• Integral structural steel wall/floor mounting stand
• Electro-static powder coated paint finish

SAFETY FEATURES
• Rotary Arm Obstruction Emergency Safety Stop Sensor

ELECTRICAL INPUT REQUIREMENT
• 115 Volts 1 Phase 60 Hz 15 Amps

Mr. Shrinkwrap is a leading distributor of protective products, shrink wrap films and installation supplies with a dedicated team available to take your order at any time of day. We have several experienced shrink wrap installation technicians on staff to help and support you on various aspects of any shrink wrap project. If you would like to place an order over the phone or have questions for us, give Mr. Shrinkwrap a call at 800-847-5290.